Page 2 of 3

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:May 26th, 2012, 9:44 pm
by Silverstreak
The pressure gauge is accurate to the show, which had a round gauge. I was thinking of installing an electrical gauge which would activate with the electronics, such as a volt meter or the ammeter below. But I'm not sure if hooking up such a device would screw up the electronics and cause the chip to malfunction.

(image pulled from Amazon, they also have similar voltmeters)

Image

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:May 27th, 2012, 7:16 am
by nstevic01
Voltage meters will not affect any of the electronics. It will simply show voltage available, I was toying the idea of gutting a volt meter and placing it behind the face of the pressure gauge, effectively making it show and go.

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:May 27th, 2012, 8:24 am
by TheWug
As someone who has built a Real Ghostbusters Proton Pack, I used a volt meter, EctoX borrowed my idea for his. It was purchased at auto zone and is circular and black, When turned on it lights up orange so it was really accurate to the cartoon. http://www.amazon.com/dp/B000FJU8I0/ref ... B000FJU8I0 Here's the link to amazon for the same one.

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:May 27th, 2012, 9:33 am
by xtrmn8r17
Looking good so far

Sent from my DROID BIONIC using Ghostbusters Fans on Android

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:May 30th, 2012, 6:23 am
by Silverstreak
As someone who has built a Real Ghostbusters Proton Pack, I used a volt meter, EctoX borrowed my idea for his. It was purchased at auto zone and is circular and black, When turned on it lights up orange so it was really accurate to the cartoon. http://www.amazon.com/dp/B000FJU8I0/ref ... B000FJU8I0 Here's the link to amazon for the same one.
That looks great, and you made an awesome pack. The gauge you picked is probably more reliable than the one I linked to also, and I like the idea of a backlight. Its a relief to hear the load of the meter + backlight didn't place too much of a voltage drop across the rest of your electronics.

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:May 30th, 2012, 7:42 am
by nstevic01
Sorry for the lack of updates guys, we had a very busy weekend. We should continue work on the pack tonight.

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:May 30th, 2012, 7:47 pm
by nstevic01
Progress, progress, progress

Me sanding what I call the "treasure chest"
Image


Worked on mounting everything up, used screws mostly. Also got the U-bolts installed
Image


Whipped up a quick bumper, will sand it down and trim it up. Prob will use it as a template with some more solid wood.
Image

Image


More to come!

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:May 31st, 2012, 6:09 am
by Silverstreak
Comin together real nice!

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:May 31st, 2012, 8:53 pm
by Mr.Spider
looks great, however, if i may, your gearbox is to wide/long. along with the yellow cylinder.

i wanna say that's the nature of these RGB packs is using one set of measurements isn't enough as certain pieces tend to be outta whack.

Other than that, it looks awesome. nothing negative. i love seeing these packs and your is turning out amazing.

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:May 31st, 2012, 9:04 pm
by nstevic01
It is a little wider than the ref pics, but we adjusted it to fit a Alice pack and my wifes back. So some creative license was used. it was hard to come up with dimensions that made each component happy, and with packs in the park coming up, we need to get it finished. If I ever make another one I will prob make it closer to the actual pack. Thanks for the compliment!

Sent from my PC36100 using Tapatalk 2

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:May 31st, 2012, 9:14 pm
by Mr.Spider
no worries, you go to packs in the park at disney too ?

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:May 31st, 2012, 9:28 pm
by nstevic01
This will be our first year. I'm hoping my shell and gun box arrive in time for my gb1 pack. You go to the one in Orlando?

Sent from my PC36100 using Tapatalk 2

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:May 31st, 2012, 9:30 pm
by Mr.Spider
yeah, i'm with orlando, we've gone for the past 2 years or so, it's a hoot lol, tons o fun

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:May 31st, 2012, 9:48 pm
by usfmichele
Yay! I'm looking forward to going. :) We haven't been to Disney in awhile...

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:June 13th, 2012, 6:30 am
by Silverstreak
Any more progress?

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:June 13th, 2012, 6:34 am
by nstevic01
Slow but steady, we have not worked on the pack in a couple of weeks due to other projects and family events. We will most likely begin production again sometime this weekend. The thrower is really the next big thing to tackle and your dimensions will give us a good starting point. Any more progress on your thrower?

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:June 13th, 2012, 6:06 pm
by Silverstreak
Slow but steady, we have not worked on the pack in a couple of weeks due to other projects and family events. We will most likely begin production again sometime this weekend. The thrower is really the next big thing to tackle and your dimensions will give us a good starting point. Any more progress on your thrower?
Great news. I didn't think you stopped working on it, I was just enjoying seeing it come together so quickly, lol.

I'm almost done with the thrower. I haven't had a chance to work on more plans though. I'm waiting for the knobs to dry (painted them silver) and getting ready to apply some movie decals for an added dose of realism. The next step will be weathering, not too sure how I'll acomplish that. I'll post pics either tomorrow night or the night after.

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:June 14th, 2012, 12:58 pm
by GBClarky
Looking real good... :-)

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:June 17th, 2012, 4:51 pm
by LandoSystem
Wow this is looking great. And thanks for sharing your tricks and specs.
Looking back, I have many more pleasant memories of the series and the toys than I do of the movies. I think I'll end up taking a crack at one of these before long.

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:June 17th, 2012, 4:59 pm
by nstevic01
Thanks everyone for all of the positive feedback. I promise we will get started on finishing it, most likely tomorrow night. Just had too many b-days, graduations, and of course father's day. So we will set up shop and prob work through til it's done.

As far as doing a mold, if anyone wants to help out with a estimate on cost of materials that would be great, I'm estimating (to do it right) around $900. This of course was based on what it cost to mold a GB1 shell.

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:June 24th, 2012, 10:33 am
by nstevic01
FINALLY got to work on the pack again, the pictures don't make it look like much but we got the pack mounted to the ALICE frame and cut the cyclotron lights. Through a series of unfortunate events, we ended up scrapping the 3/4" cyclotron cap and replacing it with 2 1/2" layers, which will make it much easier to mount the lens' and lights. We also started gluing the main pack body together and started prepping for wiring.

Image

Image

Image


We should have some more work done this week, hopefully get started on the thrower.

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:June 24th, 2012, 9:56 pm
by Silverstreak
Love it!

Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:June 25th, 2012, 12:14 am
by JoeyBaggz
Looks great, how much is the weight so far?


Sent from my MT-500 using Tapatalk

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:August 8th, 2012, 12:25 pm
by Silverstreak
Still workin on this pack?

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:August 8th, 2012, 12:28 pm
by usfmichele
Yes and no. We NEED to do it. But we get side tracked on other projects PLUS Nathan has been working on his own pack... so mine kinda got put off to the side. :P

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:August 17th, 2012, 12:52 am
by Ronnie Lee Taylor
Hope to see this finished. Its been great watching your progress so far.

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:August 17th, 2012, 7:36 am
by nstevic01
My GB1 pack is almost done, so we should be able to get back to work on this one. Sometimes you get a million projects thrown in your lap, plus family stuff. But I promise, we will finish it!!

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:September 4th, 2012, 8:10 pm
by nstevic01
Well guys, we got back to work on the pack and even made some progress:

Thrower is coming right along, to be honest this was the part of the build I was dreading, but once I got started it wasn't too bad.

Image

Image

Image


Chele started painting the components. She also came up with the idea of making the Cyclotron and Bumper on removeable assembly. So now, all we have to do is undo the 4 bolts holding the bumper on and the whole assembly comes off allowing access inside.

Image

Image


Image

Image

Image


Thats it for now.

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:September 4th, 2012, 10:05 pm
by XxEctOxX
are you light sanding in between coats?

Re: Real Ghostbusters Pack Build - Dimensions will be shared

PostPosted:September 4th, 2012, 10:07 pm
by usfmichele
I will be sanding it again. Yes.