Hello folks, and welcome to my Proton Pack build thread! This is going to be a slow-burn kinda build as it's my first attempt at prop building and I want to do it right. Also, I'm still putting parts together. My shell and motherboard are from BenofKent Props.

Ben included some very nice resin parts but I want to replace them with aluminum parts so those will end up being sold off at some point. I'm going for a GB1 build with an "accuracy vs. personal preference" caveat. Even without a full assortment of pack parts I can still pick at things so let's get started!

1 x Alice Pack Frame (GBFans)

1 x Mother Board - BenofKent

1 x Pack Body - BenofKent

1 x Ion Arm

1 x PPD - On order from FreekyGeeky

1 x HGA

1 x HGA Label - FreekyGeeky

1 x Vacuum Tube - FreekyGeeky

1 x Beam Tube - Freeky Geeky

1 x Bumper

1 x Shock Mount Bellow

1 x Booster Frame - BenofKent

2 x Injector Tube

1 x Gun Mount Bracket

1 x Shock Mount

1 x Ion Arm Assembly

2 x Alkon AQ68-P Male Connector

1 x Clippard Valve R-331

3 x Clippard #11752 Hose Barb[s] - GBFans Shop

[s]3 x Clippard #15090 L-Fitting[s] - GBFans Shop

1 x Raytheon Crank Knob #MS91528

1 x Spectra Ribbon Cable

[s]1 x Dale RH-50 Resistor (Long) -

1 x Dale PH-25 Resistor - GBFans Shop

1 x Sage Resistor (Short) - GBFans Shop

3 x #3109 Legris Gray Elbows

2 x #3175 Legris Brass Straight Male Connector

1 x Ribbon Cable Clamp[s] - GBFans Shop

5 x Hex-Head Screws

1 x Ribbon Cable Plate Set

[s]1 x 5/32” Red Tubing 5 Feet - BenofKent

1 x ¼” Blue Tubing 3 Feet - BenofKent

1 x ¼” Red Tubing 4 Feet - BenofKent

1 x 5/32” Yellow Tubing 2 Feet - BenofKent

1 x ¼” Split Loom Tubing 3 Feet - BenofKent

1 x ¾” Split Loom Tubing 7 Feet

1 x Set of Red And Blue Theater Gels for Cyclotron and Power Cell. - BenofKent

1 x Loom Clamp - Bionic Moon Labs

2 x Handle Pipes

2 x Grips

1 x Rear Instrument Bar

1 x Front Cylinder

1 x Rear Cylinder

1 x Trigger Tip (Speculated to be a gun trigger, but I doubt it ever was)

1 x Forward Knob (Next to Clippard)

1 x Stream Adjuster Knob

1 x Bottom Cosmetic Knob Large

1 x Bottom Cosmetic Knob Small

2 x Double Disk Drift Velocity Knurled Knobs (On left side of gun)

1 x Clear Acrylic Tube

1 x Clippard Valve R-701

2 x Clippard #11752 Hose Barb - GBFans Shop

1 x Gun Heatsink

3 x Toggle Switch

2 x Button Switch

3 x Light-White

1 x Light-Orange

1 x Light-Red

1 x Light-Grill (This is a white light.)

2 x Nycoil Banjo #55020

1 x Orange Cap

1 x ¼” Green Tubing 1 Foot - BenofKent

1 x 5/32 Red Tubing - BenofKent

1 x Set Of Labels - Again, Ben included a set of vinyl stickers. I want to get some rub-ons for the build, though.

1 x Power Meter Light & Cyclotron Light Kit

1 x Particle Thrower Light Kit

1 x Sound Kit

1 x 12V 9800 mAh Battery Pack

1 x WandTip Expansion Kit - Spongeface

1 x White Strobe LED - Spongeface

2 x Speakers of Some Kind

Other Parts

1 x XLR Deluxe Spengler Plate - nstevic01

Ben included some very nice resin parts but I want to replace them with aluminum parts so those will end up being sold off at some point. I'm going for a GB1 build with an "accuracy vs. personal preference" caveat. Even without a full assortment of pack parts I can still pick at things so let's get started!

**WE HAVE THE TOOLS, WE HAVE THE TALENT!****PROTON PACK**1 x Alice Pack Frame (GBFans)

1 x Mother Board - BenofKent

1 x Pack Body - BenofKent

1 x Ion Arm

1 x PPD - On order from FreekyGeeky

1 x HGA

1 x HGA Label - FreekyGeeky

1 x Vacuum Tube - FreekyGeeky

1 x Beam Tube - Freeky Geeky

1 x Bumper

1 x Shock Mount Bellow

1 x Booster Frame - BenofKent

2 x Injector Tube

1 x Gun Mount Bracket

1 x Shock Mount

1 x Ion Arm Assembly

2 x Alkon AQ68-P Male Connector

1 x Clippard Valve R-331

3 x Clippard #11752 Hose Barb[s] - GBFans Shop

[s]3 x Clippard #15090 L-Fitting[s] - GBFans Shop

1 x Raytheon Crank Knob #MS91528

1 x Spectra Ribbon Cable

[s]1 x Dale RH-50 Resistor (Long) -

*I haven't been able to find a Dale RH-50. I was able to track down a Sage M50W so it will have to do for now.*1 x Dale PH-25 Resistor - GBFans Shop

1 x Sage Resistor (Short) - GBFans Shop

3 x #3109 Legris Gray Elbows

2 x #3175 Legris Brass Straight Male Connector

1 x Ribbon Cable Clamp[s] - GBFans Shop

5 x Hex-Head Screws

1 x Ribbon Cable Plate Set

[s]1 x 5/32” Red Tubing 5 Feet - BenofKent

1 x ¼” Blue Tubing 3 Feet - BenofKent

1 x ¼” Red Tubing 4 Feet - BenofKent

1 x 5/32” Yellow Tubing 2 Feet - BenofKent

1 x ¼” Split Loom Tubing 3 Feet - BenofKent

1 x ¾” Split Loom Tubing 7 Feet

1 x Set of Red And Blue Theater Gels for Cyclotron and Power Cell. - BenofKent

*1 x Set Of Labels - Ben included some very nice vinyl labels in his kit. I'd like to find metallic labels, though.*1 x Loom Clamp - Bionic Moon Labs

**PARTICLE THROWER****1 x Particle Thrower Body - Thrower parts on order from CPU64**2 x Handle Pipes

2 x Grips

1 x Rear Instrument Bar

1 x Front Cylinder

1 x Rear Cylinder

1 x Trigger Tip (Speculated to be a gun trigger, but I doubt it ever was)

1 x Forward Knob (Next to Clippard)

1 x Stream Adjuster Knob

1 x Bottom Cosmetic Knob Large

1 x Bottom Cosmetic Knob Small

2 x Double Disk Drift Velocity Knurled Knobs (On left side of gun)

1 x Clear Acrylic Tube

1 x Clippard Valve R-701

2 x Clippard #11752 Hose Barb - GBFans Shop

1 x Gun Heatsink

3 x Toggle Switch

2 x Button Switch

3 x Light-White

1 x Light-Orange

1 x Light-Red

1 x Light-Grill (This is a white light.)

2 x Nycoil Banjo #55020

1 x Orange Cap

1 x ¼” Green Tubing 1 Foot - BenofKent

1 x 5/32 Red Tubing - BenofKent

1 x Set Of Labels - Again, Ben included a set of vinyl stickers. I want to get some rub-ons for the build, though.

**Electronics**1 x Power Meter Light & Cyclotron Light Kit

1 x Particle Thrower Light Kit

1 x Sound Kit

1 x 12V 9800 mAh Battery Pack

1 x WandTip Expansion Kit - Spongeface

1 x White Strobe LED - Spongeface

2 x Speakers of Some Kind

Other Parts

1 x XLR Deluxe Spengler Plate - nstevic01

**I'm probably missing some pieces on this list so feel free to let me know if I am! Constructive criticism is always welcome in this build.**
Last edited by H2Ghost on December 30th, 2017, 10:21 am, edited 3 times in total.

twmedford23 liked this