User avatar
By askernas
#4887857
After following countspatulas 3d files, and making the metal sides myself from 0.8mm thick aluminium, this is where I'm at.

The pedal needs a bit of paint work still, but it is winter and cold outside, and I ran out of black paint just before Christmas =p

Instead of running a wire through the hose and modifying the connectors, I have simply added a small remote control, located in the right box, that is triggered when I press the pedal. Inside the trap will be the receiver and other electronics, just wanting for smaller sprockets..

This will be fully automated as well =)

Image

https://vimeo.com/197080995
User avatar
By RamaSha007
#4888488
Not very far along one mine, but I finally got enough parts to start test fittings. Nothing here is held together by screws yet, just sorta leaning together.

Image

Although I may have to replace the gold parts. I work at the local library and used the 3d printer there to make this. Since I was gonna putty, sand, and paint most of the parts anyway, so I just used what was left over from other patrons project. The red and green parts turned out OK, but the gold parts have been cracking when doing test assembly. So a slight set back there.
By JAnderson392
Supporting Member
#4889841
I have to say this trap kit looks amazing. I started printing some parts over the weekend. I was curious about the handle and handle frame. The chart says to use increased infill. I normally print with 20%. I'm just curious as to what others have used. Would 50% be enough or should I go even higher.

Thanks,
Adam
By JAnderson392
Supporting Member
#4889843
countspatula wrote:Glad your like my kit. You shouldn't need to go a lot higher 50 should be more than enough. I usually do 30-35


Thanks for the advice. I will post pictures when I have all the parts printed.
User avatar
By thebigone2087
#4890775
Any update on the electronics kit?
User avatar
By countspatula
Supporting Member
#4890776
thebigone2087 wrote:Any update on the electronics kit?


I just finished the guides for the Door Mechanism and Smoke Pump and putting kits together. I am about halfway through the Electronics Guide which I will sell at a modest fee. I will be releasing the Door and Smoke Guides free and they do include a parts list. They will also be integrated into the Electronics Guide along with the Deluxe Trap Guide that has been tweaked to go along with electronics install.

I will most likely be releasing the Door and Smoke Guides within a week as well as the kits (depends on when rest of the parts arrive). While the door and smoke mechs can be assembled and fitted before the electronics, full integration won't be covered until Electronics Guide is done - just something to keep in mind. But with the standalone guides and the modular nature, you should be able to make them work with your own custom electronics too.

Image

Image
User avatar
By thebigone2087
#4890781
Brilliant!!!
User avatar
By tommyb345
#4894822
That's awesome!

What's the two ecigs that are needed?


countspatula wrote:Electronics Guide update - all the photos have been taken, all the steps are worked out. Have about half the guide written, working on it this week.

Image
User avatar
By countspatula
Supporting Member
#4895263
Apparently Joyetech has discontinued this line of e-cigs completely - I have not found my exact replacement yet. Search for 'automatic refillable' and look for a starter kit which will typically have 2 e-cigs, charger, etc. Automatic (pressure activated) tend to be the cigarette shaped ones we're looking for.
User avatar
By tommyb345
#4895417
Awesomesauce

countspatula wrote:My wife kindly spent the weeknd building a set of Trap electronics based on the first draft of my guide - went well, she had fun - got good feedback. Some more pictures and a round of revisions, but looking good. Soon!

Image
By spanakadakawaka
#4895419
countspatula wrote:Apparently Joyetech has discontinued this line of e-cigs completely - I have not found my exact replacement yet. Search for 'automatic refillable' and look for a starter kit which will typically have 2 e-cigs, charger, etc. Automatic (pressure activated) tend to be the cigarette shaped ones we're looking for.


I used Halo eCigs for my trap and they worked out well. They have a starter kit which comes with enough parts for two eCigs.

They are little bit wider than the Joytech so when I snapped them into the trap I think I cracked the clips slightly but overall a good option. There is a plastic cap with a hole that goes into the atomizer which is also where you draw the smoke from. The small tube from the pump can be fed sniffly throughly there for an air tight for with an additional set of tubes. It makes refilling easy to since you can remove the cap and the hose can stay in cap.
By jeffhucik
#4899568
Just bought the entire Shabang from Sean on Etsy. I need the arduino coooode! . I can reverse the engineer the wiring from th code and photos. I feel I’m a little too close to Halloween to design something myself.
Jeff

I didn't like the idea of using Zip Ties to hold t[…]

All three of my packs showed up on Friday. They l[…]

Marshmallow Baby

Even if they were hyperlinked too then one could c[…]

Oh man, I'm so behind on posts. Worked a bunch on[…]