By Tvenk
#4998755
Been lurking around for a while and me and a buddy decided it's finally time we tackled a proton pack. I've done a number of other cosplays over the years, but this is one that's been on my list for a while. Decided we wanted to mold our own and do fiberglass shells, but that there were enough resources out there we shouldn't start from total scratch.

Pack is going to be 3D printed in pieces using the MK4 files and then we'd clean up a few areas and tweak some stuff. This forum is an amazing resource. Been at it long enough now I can share a few pics of the progress.

Image
Dioxide, alphabeta001 liked this
By Tvenk
#4998757
Sanding is my least favorite part of costume/prop making and it's SO much of the effort haha

Image

Image

Image


Doing test "fits" as we go gives us motivation to keep working

Image
By Tvenk
#4998759
First layer of filler primer gives us an idea of how much work we have left but also shows how far the pieces have already come.

Image

Image

Image

Any back to the filler and sandpaper...

Image

Image
By Tvenk
#4999045
Thanks - yeah so much bondo and sanding haha.
I got them here on the forum after reading through a few threads trying to put together an updated set of plans. I believe the thread was titled: NEW GBFANS PACK PLANS
By Tvenk
#4999046
The work continues, slow and steady progress - the last 20% takes 80% of the time...

Image

Image

Image


Any now for another coat of primer - finally getting close here with finishing the buck.

Image

Image

And for some reason I got this weird crack and a bubble in a terribly inconvenient spot, so now that needs to be fixed...

Image

Image
alphabeta001 liked this
User avatar
By Demon Vice Commander
#4999051
Your master is looking good! I would recommend filling the cyclotron holes and power cell instead of molding it with them recessed; this will give you greater control over the thickness of said windows when it comes time to lay up the fiberglass and resin - otherwise you may end up with really thick windows.
Tvenk liked this
By Tvenk
#4999053
Thanks! That's helpful insight, though if I'm being perfectly honest, I don't know if I have it in me to go back and fill them in at this stage and refinish those surfaces haha. I'll have to address it with how I lay up the fiberglass on the back to make sure I can sand it down without compromising the surfaces around it.
By Tvenk
#4999538
Been a while since my latest update - too many things happening, but progress continues:

Image

Ready to start adding clay - put a little jig together to try and ensure consistent thickness
Image

Image

Image

Image

Had to redo a bunch of the keys and double check several of the walls to make sure I didn't have overhangs ahead of the fiberglass. It's amazing what you see after you walk away and come back.
Image
By Tvenk
#4999613
Fiberglass time
Image

Image

Image

Image

All trimmed up, ready for the next side. This stuff is messy (been a while since I fiberglassed). Also polyester resin is cheap which is great, but man the fumes are overpowering. Each time I took the respirator off it was wild. I'm not great at this (still some air bubbles) but was good enough to get the job done.

Image

Image

Image
By Tvenk
#4999876
The fiberglass jacket came off (with some effort) and I had more bubbles than I wanted (and created some additional overhang risk) so decided to fill those with clay. Also - since I used plastic between the clay and fiberglass, there were a number of spots where it bunched or creased that created larger impressions that would just be annoying after a silicone pour so I filled some of that stuff with clay too in order to make removal simpler later.

Oh yeah and drilled fill and air vent holes (more lessons learned on that later)


Image

Image

Image

Image



Then it was time to clean off the buck and bolt everything up properly.

Image

Image

Image
alphabeta001 liked this
By Tvenk
#5000063
And now the fun part. I definitely didn't have a large enough opening to fill over the Crank Gen which was a mistake because when the silicone would start to thicken, it didn't flow into that space well anymore. Thankfully, my vent holes were just barely large enough to be useful, though the pour was slow. I was really nervous and my vacuum pump failed on me about 2/3 of the way through so I was nervous about air bubbles, but I went slow enough I think it's going to be ok.
Used Smooth On Moldstar 30 which seemed to work great.

Image

Vacuum chamber at work
Image

Progress was slow at first
Image

Image

All finished up - very messy but I think it went pretty well. Was touch and go there for a bit - reusing containers I think spend up the catalyst on some of the later batches which had us nervous about being able to get it all in there. Would have been a lot easier with an extra Crank Gen fill hole.
Image
alphabeta001 liked this
By Tvenk
#5000146
Well, the results are IN!
You can see some places where not having that third pouring hole cause some air gaps, but it was thick enough it didn't hurt anything

Image

Image

Image

Image

Two very small air bubbles, but otherwise turned out beautifully


Image

Image
User avatar
By pchrisbosh1
#5000153
Amazing job on the mold! Looks awesome and I'm sure its going to dish out some clean casts.
Tvenk, mburkit liked this
By Tvenk
#5001390
Been a while since my last update, but progress is being made. First cast was a good learning experience (definitely came out rough) - left some air bubbles in the gel coat because I put it on too thick and resin kicked faster than I wanted leaving some poor gaps in a few corners. Structurally it'll be fine but going to need a bit more love than subsequent attempts. Other than those initial mistakes though, the casts come out real nice.

Image

Gelcoat going in:
Image

Fiberglass wasn't pushed at all into the corners at the top here and it kicked real quick. Going to have to go back and fill those gaps with resin/bondo.
Image

And then, put the gel coat on too thick so not all the air bubbles worked themselves out. Not difficult to fix, just tedious.
Image

Image

    EU orders marked as shipping today. Out of Germany[…]

    Real Ghostbusters Pop Vinyls revealed

    Just placed my pre-order for Peter Venkman on Thur[…]

    https://i.imgur.com/uiaWvf4.jpeg Here's one of […]

    Don't cross the STRINGS!

    https://i.imgur.com/CIdOafJ.jpeg I worked out t[…]