This is for other Ghostbusters Props that don't fit into the categories above.
User avatar
By Alex Newborn
#447367
I had a non-screen-accurate but very pristine one of these by the Heat Pipe Corporation, but I just scored a pretty banged-up Jordan Electronics version that was a) the correct model and b) I didn't mind altering with the addition of the belt clip.

Image

Here's a comparison of both models.

Image

I had been using the Heat Pipe version inside a small camera/cell phone pouch on my belt since it was too nice to modify, but for this one I wanted to have it visible, like in the reference pics.

Image

Closeup:
Image

At the suggestion of Brandon (Donkey8012), I removed the belt clip from an old tape measure.

Image

When I drilled the hole through the casing, the bit would only go a very shallow distance in, and then there was this scary sizzling noise. I thought at first it was emanating from my drill, and I thought the motor had caught on fire or something... then I realized it was coming from the Minirad, and that was worse, as it made me fear for a moment that I was receiving a dose of radiation! Yikes!

It subsided after a few moments, and I realized it was air escaping and hissing out through the hole.

According to the description of the prop found here, http://www.gbfans.com/equipment/other/gamma-rate-meter/, the Minirad employs "a pressurized ion chamber"... I don't think mine is pressurized anymore!

Shrug, that must've been how they made the prop, and the same thing must have happened to the one Harold Ramis used, and he seems to be doing okay thirty years on, so best not to worry about it.

Image
Image

Ready for action... except...

Image

... it doesn't have its instruction on the battery cover. Take a look at the reference pic on the Equipment pages of a more pristine Jordan Electronics Minirad...

Image

Unfortunately, I can't see the actual prop close enough in the reference pics I'm checking to tell if Ramis' sample had the lettering. After all, Egon could have tinkered with the real device to make it take supernatural readings, and could have altered the casing instructions as well.

Speaking of reference pics, I would LOVE to know where this photo came from. Can't we find it bigger anywhere?

Image

I know the Minirad can be seen on the work table in the basement, so I do plan to watch the new Blu-Ray again and hope for the best.

In the end, I will probably add the instructions eventually. I thought about finding some REALLY SMALL rubdown letters, but ye gods would that be time-consuming.

It would be so much faster to type it up and print it onto clear label paper.

Image

Of course, just when I got everything sized the way I wanted it against a 1:1 scan of the Minirad...

Image

... that's when I remembered my printer was out of black ink. Wah wah waaaah.

Alex
User avatar
By JoeLuna33
#447368
That's cool Alex. I seem to find the 179/u model a lot but I'd love to gond one of the genuine ones.
Alex Newborn liked this
User avatar
By Alex Newborn
#447371
Well, it's nice to be able to give something back, but honestly I'm just building off of the diligent research and generous information-sharing of countless fans before me.

I wasn't even going to start a thread about this item, since there's not much modification to it, but then I thought if someone else was ever doing this and like me started to freak out when the thing is outgassing, they might want to know what to expect beforehand.

Now, let's find that Egon photo in a better resolution!

Alex
Zack liked this
User avatar
By Alex Newborn
#447415
But where does it originate? Was it posted on Sony? Or was it a book? If it's a book, what is it, because I may have it somewhere and I can scan it larger.

I already went through the Ghostbusters Storybook by Anne Digby, so we can rule that one out. Making Ghostbusters by Don Shay doesn't have a lot of color images, they're all at the back, so those would be easy to check.

Or it could be a lobby card or some other promotional material. It's got to be out there somewhere.

~~~

Just realized that even though this one's a beater, I still got a real one for only a couple bucks more than what a resin copy would have cost me.

~~~

Bought a new black ink cartridge...

Image

Judging from how tall the letters are on this sticker, I would have required rubdown letters that are slightly less than 2mm tall, and I didn't find a source for any smaller than 3mm.

~~~

Also watched the 4K Blu-Ray to spot this prop. When they split up in the Sedgewick, holy cow that belt clip on the back is HUGE!

Here's some pics I found in another thread from a couple years ago...

Image

Image

Where can I find a belt clip approximately 2x3 inches?

Maybe if the drill hole for a larger belt clip is lower, I wouldn't have broken the air seal. Shrug.

~~~

By the way, did anyone ever ID any of these other tabletop items?

Image

I know the yellow box is a Voltmeter, but what about the two blue boxes?

Alex
By drjameshouse
#447458
So I checked all my screen shots, and it looks like there is text on the bottom of the minirad but there is never a clear picture from the movie. That photo that you questioned is obviously from the Gozer fight after Gozer disappears but it's not from the movie, and I can't find it in anything that I have.

The voltage meter has been discussed a little here http://www.gbfans.com/community/viewtop ... =7&t=23389. That's all I know. :)
Alex Newborn liked this
User avatar
By Alex Newborn
#447473
Oh that's a gorgeous piece! If I find one that looks that good, I'll definitely upgrade.

I also need to add a Philips head screw to the front. Do you know the length and thread size?

Did you add a belt clip to the back? Did it make that sizzling outgas sound?

I didn't know it glowed in the dark, but I just checked mine and so it does... nifty!

Alex
User avatar
By Alex Newborn
#466063
Still not as good as noslliT's, but I did upgrade to a slightly better Minirad...

Image

My other one fell on the pavement of the Space & Rocket Center* in Huntsville AL when I was getting out of the car in costume to go see Ghostbusters for $1 on the 24th of last month. The clear rectangle popped out of the gauge window. Haven't fixed it yet.

Perhaps I fated it to happen. I had already bid on the auction for this slightly better condition one, and no one else ever bid on it. So one week later, on Hallowe'en itself, the replacement arrived.

Alex

[*The place they shot the movie SpaceCamp.]
By msr322
#466725
Did you ever find any leads for that giant belt clip? I picked up a Radiacmeter on "the auction site" a few months ago, and was just getting ready to apply a regular tape measure clip onto the back. I'd rather have a slightly larger clip if you'd found any leads...
Alex Newborn liked this
By Cosmic-Riptide
#466996
Did you ever find any leads for that giant belt clip? I picked up a Radiacmeter on "the auction site" a few months ago, and was just getting ready to apply a regular tape measure clip onto the back. I'd rather have a slightly larger clip if you'd found any leads...
Nope, haven't come across anything yet.

Alex
It's a different style, but Tandy Leather just started carrying a nickel plated belt clip that fits the replica pistol belts perfectly.

http://www.tandyleatherfactory.com/en-u ... 37-00.aspx

It's pretty hefty so your Minirad should stay put, but that's also one of the down sides since you're not going to be able to just slide it on or off of your belt with just one hand.

I used a similar style clip from another company a few years ago (only availabe in black), though I didn't know at the time that I ordered that the backplate was bowed. I attached the clip to my Minirad with copper rivets (see pic below), which worked great, but the bow in the clip has since warped the back of the Minirad causing cracks to appear in the shell.

Image

The Tandy clip has a flat backplate (no bow) which should severely reduce any warping issues, but again it's hefty, so I can't promise that repeatedly taking the Minirad off of your belt and reattaching it won't stress the Minirad's shell.

The clip will also cover or partially obstruct the back screw hole on the Minirad's casing, so you'll either just have to live with your Minirad being held together with only one screw (which is what I did the first time around), or you'll have to rig up a little spring loaded tooth to take the place of the rear screw (which is what I'm hoping to try this time around).

For my second attempt I may try a gentler attaching process with some screw post rivets (copper rivets have to be hammered onto whatever your working on).

http://www.tandyleatherfactory.com/en-u ... 96-02.aspx

A problem that I've already encountered with the screw rivets is that the base posts are a little too wide for the belt clip rivet holes (I don't know how easy it will be to widen up the holes considering the clip is made of spring-steal... I may just have to sandwich a piece of aluminum with properly fitted holes between the Minirad and the clip), as well as a hair too long (but some washers should fix that).
By abaka
#4787487


According to the description of the prop found here, http://www.gbfans.com/equipment/other/gamma-rate-meter/, the Minirad employs "a pressurized ion chamber"... I don't think mine is pressurized anymore!

Shrug, that must've been how they made the prop, and the same thing must have happened to the one Harold Ramis used, and he seems to be doing okay thirty years on, so best not to worry about it.


Alex


Yeah...I was reading this thread for adding the clip to mine...I'm not sure if I'll bother now!!
User avatar
By Alex Newborn
#4805852
Came across this bit of info...

"The IM-179/PD was a miniature gamma ratemeter for placement in aircrew survival kits that employed a Neher-White pressurized ion chamber filled with argon."

So I looked up argon and it seems to be pretty safe.

"Argon has approximately the same solubility in water as oxygen, and is 2.5 times more soluble in water than nitrogen. Argon is colorless, odorless, nonflammable and nontoxic as a solid, liquid, and gas. Argon is chemically inert under most conditions and forms no confirmed stable compounds at room temperature."

Additionally: "The principal component of air is nitrogen and the only other major component is argon (about 0.9 %). Argon is chemically inert and its presence in the atmosphere poses no problem to human well being."

So apparently we breathe that gas with every lungful.

[UPDATE] Shot a video yesterday that gives a good comparison of the Minirads, among other props.



Alex
Mechanized liked this
User avatar
By Alex Newborn
#4915069
Yeah, I need to go back and repair some of the photo links if I can.

I used to do that every so often over at the RPF, but then those links began to die too, and faster than I could keep up.

Then I began putting links to my YouTube videos in my posts, as those seemed to stay active longer.

Now the video links are wonky on this site.

Alex
User avatar
By 8bitGamer1984
#4916229
Hi Mr. Newborn, I watched the movie last Night and It visible after Gozer disappears and before the building starts breaking.
That picture is when Egon says "Ray this looks very bad". However my dvd is widescreen so the Minirad's bottom was cut out. I think the photo was a remastered photo of that scene. Hope this clears things up
User avatar
By Alex Newborn
#4916721
Even the on-set photo has now been 'tweaked' by Sony, who has begun altering reference photos.

https://youtu.be/DGWMg3TfybM

Go to 5:14 to see the alterations they did to the Egon Minirad photo.

And right after that you can see one of my own Minirads.

Here's another Minirad-related video, of one of my more curious acquisitions: the clear training version.

https://youtu.be/ynlhsurlcgQ

Alex
User avatar
By One time
#4919329
Even the on-set photo has now been 'tweaked' by Sony, who has begun altering reference photos.

https://youtu.be/DGWMg3TfybM

Go to 5:14 to see the alterations they did to the Egon Minirad photo.

And right after that you can see one of my own Minirads.

Here's another Minirad-related video, of one of my more curious acquisitions: the clear training version.

https://youtu.be/ynlhsurlcgQ

Alex
This is so weird. Ghostbusters fandom is partly about painstakingly identifying props used in the 1984 movie. There's a sense of achievement in exactly identifying the obscure early 80's devices. Why delete details in photographs? Makes no sense.
User avatar
By Kingpin
Moderator
#4919360
This is so weird. Ghostbusters fandom is partly about painstakingly identifying props used in the 1984 movie. There's a sense of achievement in exactly identifying the obscure early 80's devices. Why delete details in photographs? Makes no sense.
It's Sony covering their butts for featuring stuff which may still be covered by copyright.

Ghostbusters: Tremors Ghostbusters: Breaking New[…]

Into the Dead 2 – Ghostbusters

I still need to get this Anyone here play switch[…]

I didn't know real ghostbusters / Mars attacks exi[…]

Freaky Geaky - RJ Umowski

Just received Freaky Geeky's pop mech, and extende[…]