- November 30th, 2021, 3:20 pm#4962206
This post may contain an affiliate link that helps support GBFans.com when you make a purchase at no additional cost to you.
To be honest your setup is FANTASTIC, I already bought some stuff on amazon, just struggling wiht the neopixel Ring Sizing and options right now.
A question that comes ot my mind too is... would it be possibel to interconect gbfans light board, or ghostlab lightboard with the ardafruit sound board, without having the light setup coming form arduino?
Also for the Bluetooth dongle you mean something like this right?
https://www.amazon.ca/gp/product/B01EFP ... GF3B&psc=1
Also about the coding, is there any Basic tutorial about arduino that you would reocmmend? What software do you use?
About Speakes, again, I don;t know much about it, but what other options do w ehave apart of the GBFans ones? I don;t want to wait until march tog et my steup done...
Does somehting like this works? What other alternatives do w ehave?
https://www.amazon.ca/Pyle-PLG4-2-4-Inc ... 550&sr=8-7
Also, this might sound stupid... but what cables do you recomend to wire the arduino/ardafruit stuff? Do you need a welder also?
Gucabe wrote: ↑November 30th, 2021, 2:33 pmAwesome! Its what I was planning to do witht he Wand too. So do you think its really necesary the pyle 60 watt amp step? Have you noticed the diference with and without? Would not be possible a better build speaker maybe and conect it directly to the Mixer? I'm just guessing, I don't know anything about Speakers or amps tbhdantonvfx wrote: ↑November 30th, 2021, 1:38 pmFor the audio hack I followed this video, but only did the audio hack not the rest.
Thanks so much!!!
So you opened the Wand and added a mini jack or an Aux output and conected it to a mixer/speaker right? That brings me another question, What Speakers are you using for the proton pack? Are the same for the Wand? or you have diferent ones? What mixer do you use?
About the nanopixel Ring, with your setup, would it be possibel to connect 3 diferent rings at the same time but with offsets? So they have a diferent sequence and can give that extra layer of depth instead of only one ring light?
Thanks so much again!
It goes to a Little bear MC5 Mixer, then to a pyle 60 watt amp and to a 4 inch speaker. The GBfans speaker sold in the shop is great. I use the mixer to mix 3 signals, the Adafruit fx board with the pulsecon activation audio, the neutrona wand audio and a bluetooth dongle to send the music from my phone.
Its definetly possible to add more layers, just remember that neopixels are conected in series, if you put pixels in parallel they will do the same effect as the others. So if you want different sequences they have to be daisy chained.
To be honest your setup is FANTASTIC, I already bought some stuff on amazon, just struggling wiht the neopixel Ring Sizing and options right now.
A question that comes ot my mind too is... would it be possibel to interconect gbfans light board, or ghostlab lightboard with the ardafruit sound board, without having the light setup coming form arduino?
Also for the Bluetooth dongle you mean something like this right?
https://www.amazon.ca/gp/product/B01EFP ... GF3B&psc=1
Also about the coding, is there any Basic tutorial about arduino that you would reocmmend? What software do you use?
About Speakes, again, I don;t know much about it, but what other options do w ehave apart of the GBFans ones? I don;t want to wait until march tog et my steup done...
Does somehting like this works? What other alternatives do w ehave?
https://www.amazon.ca/Pyle-PLG4-2-4-Inc ... 550&sr=8-7
Also, this might sound stupid... but what cables do you recomend to wire the arduino/ardafruit stuff? Do you need a welder also?