- February 13th, 2023, 5:04 pm#4978828
Mr. Burkit, are you still planning to do a build thread chronicling your processes?
- February 14th, 2023, 10:41 am#4978845
GBKid1984 wrote: ↑February 13th, 2023, 5:04 pm Mr. Burkit, are you still planning to do a build thread chronicling your processes?I am not sure if I will or not. My pack has been done since October of last year at this point. I have a lot of photos of my build in this research thread, so I do not know if any service could be had if I had a specific build thread .
My Hero OMNI Pack Build: Click Here
My Stantz Pack Build: Click Here
My GB2 Semi-hero Pack: Click Here
My GB:TVG Pack: Click Here
My Stantz Pack Build: Click Here
My GB2 Semi-hero Pack: Click Here
My GB:TVG Pack: Click Here
- February 16th, 2023, 9:07 pm#4978932
Hey this is the guy from YouTube, do I have the right person here? Complete noob to operating around this page even tho I been a member for a long time
- February 20th, 2023, 3:53 pm#4979059
What is the correct size cap screws to use for the ion arm resistors?
- February 20th, 2023, 4:40 pm#4979061
Spectregater wrote: ↑February 20th, 2023, 3:53 pm What is the correct size cap screws to use for the ion arm resistors?4-40. They're a very similar size to M3 if you're using metric sizes.
Spectregater liked this
- February 25th, 2023, 9:54 pm#4979230
mburkit wrote: ↑January 27th, 2022, 1:48 pmI was wondering what size diameter hose did you use and how long. Did you use a stencil on your hose? Any help would be appreciated thanks
Last edited by Kingpin on February 27th, 2023, 2:53 am, edited 2 times in total.Reason: Removed unnecessarily quoted content.
- February 26th, 2023, 1:07 pm#4979255
mburkit wrote: ↑August 1st, 2021, 10:55 am Next set of parts.OK so the 1/8x1/4 compression union doesn't exist. 1/8 is to small for the red hose. 1/8 is 3.18mm the hose size is 4mm. This is why they use the smc 4mm. 4mm hose will need 5/32 fitting. You can find this on gbfans.com
JMF 3/8" x 1/4" Compression Union
(You need 1 of these on the left of the EDA)
NOTE: The Legris straights on the pack were replaced with JMF 1/8" x 1/4" Compression Union. I don't have these on hand yet to share photos of.
Last edited by Kingpin on February 27th, 2023, 2:53 am, edited 2 times in total.Reason: Removed unnecessarily quoted content.
- February 26th, 2023, 6:51 pm#4979262
Iamreadytobelieve wrote: ↑February 26th, 2023, 1:07 pmThey do exist as I have some of them. But you are correct that they were the wrong size. The reason I originally went with that size was due to photo scaling. I did end up finding some 5/32 fittings that are currently on my pack.
OK so the 1/8x1/4 compression union doesn't exist. 1/8 is to small for the red hose. 1/8 is 3.18mm the hose size is 4mm. This is why they use the smc 4mm. 4mm hose will need 5/32 fitting. You can find this on gbfans.com
Iamreadytobelieve wrote: I was wondering what size diameter hose did you use and how long. Did you use a stencil on your hose? Any help would be appreciated thanksThere was an individual in one of the facebook groups I belong to that ended up replicating that specific hose. I'd have to pull my pack out of storage to measure the outer diameter of the hosing for you.
My Hero OMNI Pack Build: Click Here
My Stantz Pack Build: Click Here
My GB2 Semi-hero Pack: Click Here
My GB:TVG Pack: Click Here
My Stantz Pack Build: Click Here
My GB2 Semi-hero Pack: Click Here
My GB:TVG Pack: Click Here
- February 27th, 2023, 1:33 pm#4979289
mburkit wrote: ↑February 26th, 2023, 6:51 pmHey I went to a plumbing and hydraulic hose store in one! I measured the proton pack side fittings and have settled on 3/16 brass fittings. This is larger and looks right! The red hose is still able to fix inside with a bit of room. The opening is a bit bigger than 4.5mm. This .188 of an inchIamreadytobelieve wrote: ↑February 26th, 2023, 1:07 pmThey do exist as I have some of them. But you are correct that they were the wrong size. The reason I originally went with that size was due to photo scaling. I did end up finding some 5/32 fittings that are currently on my pack.
OK so the 1/8x1/4 compression union doesn't exist. 1/8 is to small for the red hose. 1/8 is 3.18mm the hose size is 4mm. This is why they use the smc 4mm. 4mm hose will need 5/32 fitting. You can find this on gbfans.comIamreadytobelieve wrote: I was wondering what size diameter hose did you use and how long. Did you use a stencil on your hose? Any help would be appreciated thanksThere was an individual in one of the facebook groups I belong to that ended up replicating that specific hose. I'd have to pull my pack out of storage to measure the outer diameter of the hosing for you.
- February 27th, 2023, 9:27 pm#4979293
I am assuming you want to change the screws on the bumper and bottom of the pack...plus the one by the metal v hook. I used 1/4-20 3/8 worked well. I used a 7/32 drill bit before screwing the 1/4-20 in. The screws will cut in and hold without glue! If you need reference video look for proton pack is not a toy on YouTube! He is awesome and in the comments is the better screw size to use not what he used.
- February 27th, 2023, 11:59 pm#4979298
Iamreadytobelieve wrote: ↑February 27th, 2023, 9:27 pm I am assuming you want to change the screws on the bumper and bottom of the pack...plus the one by the metal v hook. I used 1/4-20 3/8 worked well. I used a 7/32 drill bit before screwing the 1/4-20 in. The screws will cut in and hold without glue! If you need reference video look for proton pack is not a toy on YouTube! He is awesome and in the comments is the better screw size to use not what he used.Yah I am but I’ve seen conflicting info on whether to use 1/4-20 or 10-32. Mack’s factory uses 10-32 and they are basing it off the super hero pack but I know the gb1 hero pack uses 1/4-20 socket caps. So I dunno
- February 28th, 2023, 8:43 pm#4979339
jonogunn wrote: ↑February 27th, 2023, 11:59 pmThis is what Mine look likeIamreadytobelieve wrote: ↑February 27th, 2023, 9:27 pm I am assuming you want to change the screws on the bumper and bottom of the pack...plus the one by the metal v hook. I used 1/4-20 3/8 worked well. I used a 7/32 drill bit before screwing the 1/4-20 in. The screws will cut in and hold without glue! If you need reference video look for proton pack is not a toy on YouTube! He is awesome and in the comments is the better screw size to use not what he used.Yah I am but I’ve seen conflicting info on whether to use 1/4-20 or 10-32. Mack’s factory uses 10-32 and they are basing it off the super hero pack but I know the gb1 hero pack uses 1/4-20 socket caps. So I dunno
- February 28th, 2023, 9:04 pm#4979340
Iamreadytobelieve wrote: ↑February 28th, 2023, 8:43 pmAnd that's 1/4-20 with #10 washers?jonogunn wrote: ↑February 27th, 2023, 11:59 pmThis is what Mine look like
Yah I am but I’ve seen conflicting info on whether to use 1/4-20 or 10-32. Mack’s factory uses 10-32 and they are basing it off the super hero pack but I know the gb1 hero pack uses 1/4-20 socket caps. So I dunno
- March 1st, 2023, 9:54 am#4979353
This post may contain an affiliate link that helps support GBFans.com when you make a purchase at no additional cost to you.
https://www.ebay.ca/itm/115627786980?ep ... BMtpmt4dNh
https://www.ebay.ca/itm/295547319843
mburkit wrote: ↑August 1st, 2021, 10:43 am Okay, time for some close ups of the parts.For the people who are interested I have found the neutrik NAC3FX-W and neutrik NAC3MPX on ebay
Flexo PET - 1/2" - PTN0.50YB
Neutrik NAC3FX-W
Neutrik NAC3MPX
(Before modification)
(After modification)
Neutrik NAC3FX-W and Neutrik NAC3MPX connected
Herbert Cooper 35" Mask Scuba Rebreather HC36S M25A1 Oxygen Hose
Heinemann Electric 70-592A Circuit Breaker 1Amp 115v
Leviton 15 amp Single-Pole Toggle Light Switch
(All ready chopped up, painted with fiberglass rod attached to mimic the Heinemann Circuit Breaker)
https://www.ebay.ca/itm/115627786980?ep ... BMtpmt4dNh
https://www.ebay.ca/itm/295547319843
- March 1st, 2023, 10:02 am#4979354
jonogunn wrote: ↑February 28th, 2023, 9:04 pm1/4 -20 -3/8!...3/8 is the length...I can't remember washer size. You will know because they fit perfectly in the space that hasbro left.Iamreadytobelieve wrote: ↑February 28th, 2023, 8:43 pmAnd that's 1/4-20 with #10 washers?
This is what Mine look like
jonogunn liked this
- March 1st, 2023, 10:33 am#4979358
Does anyone know what is the correct name of the JST two pin connector.... for example jst ph 2 pin. I would like to put in the talentcell and want to purchase the connector and usb and wire it up myself. I just don't see the point in paying an increased price for something so simple.I just may have to open it up and take a look.
- March 17th, 2023, 11:51 am#4980099
How did you wire up the neutrik NAC3MPX to the wand??? Did you use and modified the battery tray. Or did you just opened up the wand and wired it up that way?
Last edited by Kingpin on March 17th, 2023, 1:34 pm, edited 2 times in total.Reason: Removed unnecessarily quoted content.
- March 21st, 2023, 10:36 am#4980294
Iamreadytobelieve wrote: ↑March 17th, 2023, 11:51 am How did you wire up the neutrik NAC3MPX to the wand??? Did you use and modified the battery tray. Or did you just opened up the wand and wired it up that way?My pack is not a Haslab pack. Mine is made the same way the ones for the film were made. My wand is fully aluminum made by the same person that made them for the film. I also created my own electronics.
My Hero OMNI Pack Build: Click Here
My Stantz Pack Build: Click Here
My GB2 Semi-hero Pack: Click Here
My GB:TVG Pack: Click Here
My Stantz Pack Build: Click Here
My GB2 Semi-hero Pack: Click Here
My GB:TVG Pack: Click Here
- March 21st, 2023, 6:07 pm#4980315
mburkit wrote: ↑March 21st, 2023, 10:36 amThank you!Iamreadytobelieve wrote: ↑March 17th, 2023, 11:51 am How did you wire up the neutrik NAC3MPX to the wand??? Did you use and modified the battery tray. Or did you just opened up the wand and wired it up that way?My pack is not a Haslab pack. Mine is made the same way the ones for the film were made. My wand is fully aluminum made by the same person that made them for the film. I also created my own electronics.
- May 18th, 2023, 8:44 pm#4982493
What screws are used on the trigger box of the Afterlife thrower? On the Haslab thrower, they look like some kind of hex screws but I’m building a thrower and want to know the exact size and type of screw they are.
- May 19th, 2023, 3:22 am#4982499
mgsrex08 wrote: ↑May 18th, 2023, 8:44 pm What screws are used on the trigger box of the Afterlife thrower? On the Haslab thrower, they look like some kind of hex screws but I’m building a thrower and want to know the exact size and type of screw they are.They're definitely socket cap screws. They look pretty small, so probably 4-40.
mburkit liked this