- February 10th, 2023, 3:06 am#4978682
The instructions have been posted:
gamera1968 liked this
Bluestreak wrote: ↑February 10th, 2023, 7:39 am So... anyone have a lead on an aluminum motherboard yet?
Mercifull wrote: ↑February 9th, 2023, 3:40 am It loads for me. Maybe you were logged out?Yes, I wasn't logged in. Weird. Now it played.
Mercifull wrote: ↑February 10th, 2023, 3:06 am The instructions have been posted:This is great! Thank you so much.
Mercifull wrote: ↑February 12th, 2023, 12:25 am Just get a selection box of resistors. Shouldn’t cost you more than 10 for like 600 resistors or various types. Amazon or eBay deliver to you fast.Much thanks clearing that up.
The body colour of the resistor just indicate the type of core, either metal oxide film (1-2% tolerance) or carbon film (5% tolerance). Either type will work.
The important thing is that you get 47 and 470 ohm resistors. Don’t worry about sourcing the exact types in the images.
jonogunn wrote: ↑February 12th, 2023, 3:53 am Can anyone confirm the official pan head bolt sizes for the afterlife pack? I think Adam savage said they are 10-24’s. If that is accurate would that apply to the bumper as well?
Mercifull wrote: ↑February 12th, 2023, 2:54 am Generally it’s good practice to put your resistors all going the same direction (I.e gold stripe on the left) but it doesn’t actually matter which way around they go.Thank you very much - I really do appreciate it.
gamera1968 wrote: ↑February 11th, 2023, 8:13 pmI have all the necessary parts and I'll be doing the mod tonight, finallyIMercifull wrote: ↑February 10th, 2023, 3:06 am The instructions have been posted:
jangos_head wrote: ↑February 26th, 2023, 8:33 am Dear allIf you haven’t already, try fresh batteries
This is my first post. I am a pretty newbie.
I was wondering does anyone have this issue?
I connect my wand to my pack. When I fire up my wand, after hitting the 1st, 2nd and 3rd switch it works fine.
Then sometimes I noticed then when I do it again, when I hit the 3rd switch, it powers down the wand and then powers down the pack as well.
Not sure why that is happening. The 3rd switch just power off the wand and then proceed to power down pack
Worried I got a defective pack
Help me GB fans. You are my only hope
Bluestreak wrote: ↑February 10th, 2023, 7:39 am So... anyone have a lead on an aluminum motherboard yet?I'm working on one right now. I have a friend of mine cutting one out for me right now, if I got the dimensions correct I'd be willing to share the DXF file.
Nighty80 wrote: ↑March 27th, 2023, 11:02 am That looks great!Yes, it does have an ALICE Frame on it. Have noticed though, the pack slides slightly forward over a period of time and the N-Filter starts pressing against the glass on the door. I can push the pack back and it gives about an inch clearance, but the pack will slide forward again. It doesn't press hard enough against the glass to cause concern of it breaking, but I'm thinking of putting something (some type of skid resistant tape) under the stand to prevent the pack from sliding forward.
Do you have an Alice frame on your pack? Really tempted by one of these (assuming at some point I take it off long enough to display )
Dragonfire82877 wrote: ↑March 27th, 2023, 11:40 am I'm thinking of putting something (some type of skid resistant tape) under the stand to prevent the pack from sliding forward.Maybe a clear silicone dot like what is used on the back of a picture frame to keep it from rubbing against the wall.
Ecto24601 wrote: ↑March 27th, 2023, 2:19 pm Hey Dragonfire, would there be a way to display the pack with wand attached in the display case? Or is the pack too wide with the wand attached? I guess it will only fit if you remove the top shelf. Wish IKEA would have worked in more slots to have the glass bottom set higher. I'm considering the Fabrikör myself for display, but really wanna display it with the wand on it.Unfortunately, there doesn’t appear to by any way to have the wand holstered. Even if you were able to fit the pack in the cabinet with the wand holstered, the stiff “rebreather hose” wouldn’t allow for the pack to fit.
I've just finished a second read-through. Thank […]
An awesome update, I loved Blue's work on O Human[…]
I know its not entirely related to Firehouse, […]
sNenUCsNhE4 Eight months on since developer I[…]