[Murdock]

This post may contain an affiliate link that helps support GBFans.com when you make a purchase at no additional cost to you.

Oh that's super helpful actually, thanks.

Did some searching and found something that looks about right. The top lip seems to be about right.

http://amazon.com/Thermos-Vacuum-Insula ... B09P1DMCT1

Sorry if I did hi-jack this but also thought it belonged to here as well, since it is related to sourcing the part.

Well I regret to inform that it is not a match, diameter is pretty close, but it's about 2 inches too short as well as the profile isn't right.

Kinda of a bummer.

[mike_waclo]

So the US version of the flask from Amazon is similar, but definitely a different size, and has some different geometry overall. Might be "close enough" to work with, but I don't know if it'll fit properly with the printed parts just yet.

[Spectregater]

Its the exact same size as all the others I have found here in the US. Guess ill stick to my spray paint idea. Its crazy how so many things sold in the UK don't have a US equivalent.

I will have to check it out. All I could find was a white plastic one that was the correct size. I was just going to spray paint it satin nickel.

Starting to work on mine after a friend hooked me up with the thermos from overseas.

I got them to send me the handle...for those stateside, Lowes has this version which is marginally smaller diameter, but will work fine.

https://www.lowes.com/pd/allen-roth-3-i ... ll/1062915

[Spectregater]

Ive got everything I need except the electronics kit. I am #17 on the waitlist. However ive yet to even start putting it together.

[Spectregater]

So I asked on facebook on the EctoLabs page, but have yet to receive an answer. How are the three main parts of the thrower held together? Screws or 2 part epoxy? Also what other screws are needed?

[tobycj]

What parts do you mean? The thermos bracer used screws, assuming that's one of the parts you mean.

[Spectregater]

The main body, the front shroud, fuse box and trigger box.

[EctoLabs]

The main body, the front shroud, fuse box and trigger box.

The shroud is glued to the main body with epoxy (it's also strengthened by the aluminium tube that runs through both). The fuse box can either be glued or, if you are using my files, there are holes for 4x M3 bolts that are tightened inside the fuse box itself.

[Spectregater]

The main body, the front shroud, fuse box and trigger box.

The shroud is glued to the main body with epoxy (it's also strengthened by the aluminium tube that runs through both). The fuse box can either be glued or, if you are using my files, there are holes for 4x M3 bolts that are tightened inside the fuse box itself.

Does the arm brace once mounted to the body base screw into the main body with 4 M3 bolts as well?

[EctoLabs]

Yeah, 4x M4 bolts in the base (black hex bolts will look best). You'll want to screw the base to the body before adding the brace as the brace overhangs those holes in the base. Use locknuts inside so you can screw on the brace without it coming loose.

[Spectregater]

I guess the last screws I need are the four that hold in the little plate that the hose goes into on the trigger box.

[tobycj]

I guess the last screws I need are the four that hold in the little plate that the hose goes into on the trigger box.

There were only two, bottom left and top right corners. Probably M3 looking at the ref pics.

[Spectregater]

I guess the last screws I need are the four that hold in the little plate that the hose goes into on the trigger box.

There were only two, bottom left and top right corners. Probably M3 looking at the ref pics.

That's the fuse box. the trigger box plate has four screw holes.

[tobycj]

There were only two, bottom left and top right corners. Probably M3 looking at the ref pics.

That's the fuse box. the trigger box plate has four screw holes.

Just realised I misread your post! In the BTS pics where you can make them out clearly enough there are only two screws used, despite four holes being apparent

[Spectregater]

This post may contain an affiliate link that helps support GBFans.com when you make a purchase at no additional cost to you.

This is the last part that is elusive for me to find here in the US. Does anyone have any leads?
2x 13mm OD yellow screw caps - https://www.amazon.co.uk/dp/B0CXR2QJ1T? ... ct_details

[AJ Quick]

This is awesome, great work!