Selling my complete Real Ghostbusters Firehouse playset made by Kenner.
$275 + S&H
Liev Skelton
Northfield, MN
I’ve had this for about a decade, and it’s pretty much just been displayed on my shelf since. Made sure to keep it out of the sun, so the plastic isn’t discolored. Despite it’s …
Decided to finally tackle the famous colander helmet from the first film. Most of the research I used to assemble it was either screenshots from the movie or replicas made by CountSpatula or ManCavePuzzles.
Found one of the accurate colanders on eBay, drilled out the rivets holding in the handles a…
Began working on some leg hose connectors. Used pics of the screen-used as a reference, and assembled them in Microsoft 3D Builder. Left is GB1/2, right is FE Engineer.
The hole in the GB1/2 connector is measured to fit 1/2" OD tubing, which I’ll include (dyed or clear) with the connector once I pr…
Got this 1984 wand for Crimbus, so I immediately began modifying it.
Started by cutting the excess plastic around the mounting ring in the foregrip to give it the 90° twisting motion, cracked open the foregrip itself so I could cut out the tactile mode change switch and attach the wires to an accur…
I just got a 1984 wand as a Crimbus gift, and I’ve already begun the modding process. I managed to pop out the vent light cover and make the grip twistable, but I can’t seem to pop the two halves open. I can see screws, they just don’t seem to want to come out for some reason.
EDIT: Ignore me. I go…
Showcasing my (mostly) finished Ghostbusters flight suit. I say “mostly” because it’s usually in a constant state of flux between finished and me later upgrading some part of it.
The base suit is a khaki Tru-Spec 27-P, arm patch from Amazon, as well as the custom name tag (went with the velcro base…
Finished up a quick stunt version of Sean Charlesworth’s Ghost Trap pedal.
The printed parts are fantastic, and I’m pretty happy with the final result. I didn’t have any corrugated tubing for under the plate, so I substituted it with some foam I had on hand. There are also some other parts that are…
Been wanting to make a belt gizmo replica for a while, but I’m not sure what to use for the base board. I know there’s already plenty of complete replicas and kits out there, but I’d like to make one myself that still uses a calculator board, ideally without paying the $1000 cost that the ICC-808D m…
Made this little short featuring some of my Ghostbusters props set to some music from Afterlife, as well as the dialog from the commercial in the first film. I also added some matching sound effects.
<a href="https://www.youtube.com/watch?v=6s4DqjVDghY" class="onebox" target="_blank" rel="noopener">https://www.youtube.com/watch?v=6s4DqjVDghY</a>
After months of this thing sitting on my worktable, I finally finished converting my <a href="http://HalloweenCostumes.com">HalloweenCostumes.com</a> PKE into a somewhat better replica, however this was not a painless process. What I expected to be a simple transfer of electronics into a new shell turned into hours of re-soldering almost eve…
Sign in to post on leocor-replicas's wall.
Started a forum topic: FOR SALE: Kenner Real Ghostbusters Firehouse Playset
Selling my complete Real Ghostbusters Firehouse playset made by Kenner. $275 + S&H Liev Skelton Northfield, MN I’ve had this for about a decade, and it’s pretty much just been displayed on my shelf since. Made sure to keep it out of the sun, so the plastic isn’t discolored. Despite it’s …
Read moreStarted a forum topic: Aura-Video Analyzer build
Decided to finally tackle the famous colander helmet from the first film. Most of the research I used to assemble it was either screenshots from the movie or replicas made by CountSpatula or ManCavePuzzles. Found one of the accurate colanders on eBay, drilled out the rivets holding in the handles a…
Read moreStarted a forum topic: Leg Hose Connectors
Began working on some leg hose connectors. Used pics of the screen-used as a reference, and assembled them in Microsoft 3D Builder. Left is GB1/2, right is FE Engineer. The hole in the GB1/2 connector is measured to fit 1/2" OD tubing, which I’ll include (dyed or clear) with the connector once I pr…
Read moreStarted a forum topic: Hasbro 1984 Neutrona Wand conversion.
Got this 1984 wand for Crimbus, so I immediately began modifying it. Started by cutting the excess plastic around the mounting ring in the foregrip to give it the 90° twisting motion, cracked open the foregrip itself so I could cut out the tactile mode change switch and attach the wires to an accur…
Read moreStarted a forum topic: Advice on separating the foregrip on the 1984 Hasbro wand?
I just got a 1984 wand as a Crimbus gift, and I’ve already begun the modding process. I managed to pop out the vent light cover and make the grip twistable, but I can’t seem to pop the two halves open. I can see screws, they just don’t seem to want to come out for some reason. EDIT: Ignore me. I go…
Read moreStarted a forum topic: My flight suit.
Showcasing my (mostly) finished Ghostbusters flight suit. I say “mostly” because it’s usually in a constant state of flux between finished and me later upgrading some part of it. The base suit is a khaki Tru-Spec 27-P, arm patch from Amazon, as well as the custom name tag (went with the velcro base…
Read moreStarted a forum topic: Quick Charlesworth pedal build
Finished up a quick stunt version of Sean Charlesworth’s Ghost Trap pedal. The printed parts are fantastic, and I’m pretty happy with the final result. I didn’t have any corrugated tubing for under the plate, so I substituted it with some foam I had on hand. There are also some other parts that are…
Read moreStarted a forum topic: Alternative calculator models to the Sanyo ICC-808D for a belt gizmo replica?
Been wanting to make a belt gizmo replica for a while, but I’m not sure what to use for the base board. I know there’s already plenty of complete replicas and kits out there, but I’d like to make one myself that still uses a calculator board, ideally without paying the $1000 cost that the ICC-808D m…
Read moreStarted a forum topic: The Ghostbusters Workbench
Made this little short featuring some of my Ghostbusters props set to some music from Afterlife, as well as the dialog from the commercial in the first film. I also added some matching sound effects. <a href="https://www.youtube.com/watch?v=6s4DqjVDghY" class="onebox" target="_blank" rel="noopener">https://www.youtube.com/watch?v=6s4DqjVDghY</a>
Read moreStarted a forum topic: Rubie's/HalloweenCostumes.com PKE meter replica conversion.
After months of this thing sitting on my worktable, I finally finished converting my <a href="http://HalloweenCostumes.com">HalloweenCostumes.com</a> PKE into a somewhat better replica, however this was not a painless process. What I expected to be a simple transfer of electronics into a new shell turned into hours of re-soldering almost eve…
Read more